Bitcraze Wiki

User Tools

Site Tools

You are here: index » doc » crazyradio » usb
Trace:
doc:crazyradio:usb:index

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Next revision Both sides next revision
doc:crazyradio:usb:index [2012-04-02 08:54]
arnaud [Data transfer] 		doc:crazyradio:usb:index [2012-05-14 07:50]
arnaud [Dongle configuration]
Line 1: Line 1:
 ====== Usb and Radio protocol of the Crazyradio dongle ====== ====== Usb and Radio protocol of the Crazyradio dongle ======
  
-The Crazyradio dongle is based on a Nordic semiconductor nRF24LU1 chip. The radio communication is done using the Nordic "Enhanced ShockBurst™" packet protocol with acknoledge. Variable size packet, from 1 to 32 bytes, can be send and acknoledged by the copter. The acknoledgement packet can contains a payload from 0 to 32Bytes.+The Crazyradio dongle is based on a Nordic semiconductor nRF24LU1 chip. The radio communication is done using the Nordic "Enhanced ShockBurst™" packet protocol in PTX mode with acknoledge. Variable size packet, from 1 to 32 bytes, can be send and acknoledged by the copter. The acknoledgement packet can contains a payload from 0 to 32Bytes.
  
-This page document the protocol used in the version 0.33 of the Crazyradio dongle. Future version (up to 1.0) will be kept compatible.+This page document the protocol used in the version 0.40 of the Crazyradio dongle. Future version (up to 1.0) will be kept compatible.
  
 ===== USB protocol ===== ===== USB protocol =====
  
-The USB devices have the VID/PID couple 0x1915/0x7777. Two bulk endpoint are configured:+The USB devices have the VID/PID couple 0x1915/0x7777.
  
 | EP0 | Control | Control endpoint. Used to configure the dongle | | EP0 | Control | Control endpoint. Used to configure the dongle |
-| EP1 | Bulk    | Data endpoint. Used to send and receive radio packets |+| EP1IN/OUT | Bulk    | Data endpoints. Used to send and receive radio packets |
  
 ==== Dongle configuration ==== ==== Dongle configuration ====
 +
 +Crazyradio vendor requests summary:
 +
 +^ bmRequestType ^ bRequest                 ^ wValue   ^ wIndex ^ wLength ^ data    ^
 +|          0x40 | SET_RADIO_CHANNEL (0x01) | channel  | Zero   | Zero    | None    |
 +|          0x40 | SET_RADIO_ADDRESS (0x02) | Zero     | Zero   | 5       | Address |
 +|          0x40 | SET_DATA_RATE (0x03)     | Datarate | Zero   | Zero    | None    |
 +|          0x40 | SET_RADIO_POWER (0x04)   | Power    | Zero   | Zero    | None    |
 +|          0x40 | SET_RADIO_ARD (0x05)     | ARD      | Zero   | Zero    | None    |
 +|          0x40 | SET_RADIO_ARC (0x06)     | ARC      | Zero   | Zero    | None    |
 +|          0x40 | SET_CONT_CARRIER (0x20)  | Active   | Zero   | Zero    | None    |
 +|          0x40 | LAUNCH_BOOTLOADER (0xFF) | Zero     | Zero   | Zero    | None    |
 +
 +=== Set radio channel ===
 +
 +^ bmRequestType ^ bRequest                 ^ wValue   ^ wIndex ^ wLength ^ data    ^
 +|          0x40 | SET_RADIO_CHANNEL (0x01) | channel  | Zero   | Zero    | None    |
 +
 +The nrf24L chips provides 126 Channels of 1MHz from 2400MHz to 2525MHz. The channel parameter shall be between 0 and 125 (if not the command will be ignored).
 +
 +The radio channel is set as soon as the setup transaction is completed which takes about 1ms. The new frequency is going to be used for the following transfered packets. Default value for the radio channel is 2.
 +
 +=== Set radio address ===
 +
 +^ bmRequestType ^ bRequest                 ^ wValue   ^ wIndex ^ wLength ^ data    ^
 +|          0x40 | SET_RADIO_ADDRESS (0x02) | Zero     | Zero   | 5       | Address |
 +
 +The packet sent by the radio contains a 5 bytes address. The same address must be configured in the receiver for the communication to work.
 +
 +The address must follow the requirement of the section 6.4.3.2 of the nRF24LU1 documentation:
 +
 +<code>
 +Addresses where the level shifts only one time (that is, 000FFFFFFF) can often be detected in
 +noise and can give a false detection, which may give a raised Packet-Error-Rate. Addresses
 +as a continuation of the preamble (hi-low toggling) raises the Packet-Error-Rate.
 +</code>
 +
 +The default address is 0xE7E7E7E7E7.
 +
 +=== Set datarate ===
 +
 +^ bmRequestType ^ bRequest                 ^ wValue   ^ wIndex ^ wLength ^ data    ^
 +|          0x40 | SET_DATA_RATE (0x03)     | Datarate | Zero   | Zero    | None    |
 +
 +Possible values for the datarate:
 +^ Value ^ Radio datarate ^
 +|     0 | 250Kbps        |
 +|     1 | 1MBps          |
 +|     2 | 2Mbps (Default)|
 +
 +
 +=== Set radio power ===
 +
 +=== Configure auto retry (ARD/ARC) ===
 +
 +=== Continuous carrier mode ===
 +
 +=== Launch bootloader ===
 +
  
 ==== Data transfer ==== ==== Data transfer ====
Line 35: Line 94:
 This protocol permits to transfer about 500 packets per seconds. This protocol permits to transfer about 500 packets per seconds.
 ===== Radio protocol ===== ===== Radio protocol =====
- 
  
  
  
doc/crazyradio/usb/index.txt · Last modified: 2020-05-12 14:12 by kimberly

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki