User Tools

Site Tools


misc:hacks:topleddeck

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
misc:hacks:topleddeck [2019-06-04 10:57]
kimberly
misc:hacks:topleddeck [2019-06-04 12:20] (current)
kimberly
Line 1: Line 1:
 ====== LED deck on top with flow deck ====== ====== LED deck on top with flow deck ======
  
-With the LED deck and a Crazyflie 2.x, we are able to make real pieces of art, like in the light paintings in this [[https://​www.bitcraze.io/​2019/​03/​lighthouse-painting/​|blog post]] or even the [[https://​www.bitcraze.io/​2019/​03/​drawing-images-with-crazyflie-and-bitcraze-at-icra-2019/​| Mona lisa]]. However, these fun projects do require an external positioning system, since we used the  [[https://​www.bitcraze.io/​lighthouse-positioning-deck/​|lighthouse positioning deck]]+With the [[https://​www.bitcraze.io/​led-ring-deck/​|LED deck]] and a Crazyflie 2.x, we are able to make real pieces of art, like in the light paintings in this [[https://​www.bitcraze.io/​2019/​03/​lighthouse-painting/​|blog post]] or even the [[https://​www.bitcraze.io/​2019/​03/​drawing-images-with-crazyflie-and-bitcraze-at-icra-2019/​| Mona lisa]]. However, these fun projects do require an external positioning system, since we used the  [[https://​www.bitcraze.io/​lighthouse-positioning-deck/​|lighthouse positioning deck]] ​(but you can also use the LPS or MoCap system)
  
 __How about using the LED-deck in the combination with the [[https://​www.bitcraze.io/​flow-deck-v2/​|Flow deck v2]]?__ A while ago we managed to do this by drilling a couple of holes in the LED deck in this [[https://​www.hackster.io/​krichardsson/​light-paint-with-a-drone-d050af|hackster project]]. However, if you are fine with putting the LED deck on the top, there might be an easier way to achieve this combination. __How about using the LED-deck in the combination with the [[https://​www.bitcraze.io/​flow-deck-v2/​|Flow deck v2]]?__ A while ago we managed to do this by drilling a couple of holes in the LED deck in this [[https://​www.hackster.io/​krichardsson/​light-paint-with-a-drone-d050af|hackster project]]. However, if you are fine with putting the LED deck on the top, there might be an easier way to achieve this combination.
Line 12: Line 12:
   * Hotglue or tape   * Hotglue or tape
  
-What we are essentially doing, is that we are flipping the pin-layout of the LEDdeck ​so that it is compatible ​with the crazyflie ​to be put on the top.+What we are essentially doing, is that we are flipping the pin-layout of the LED deck so that it is compatible to be put on the top of the Crazyflie.
  
-The image below shows how you should solder the wiring. The **Gnd** (ground),** IO2**, **OW** (deck memory), and **VCOM** (power supply). Please check out this [[projects:​crazyflie2:​expansionboards:​index|page]] to confirm for yourself ​what the pinout is for the expansion decks are+The image below shows how you should solder the wiring. The **Gnd** (ground),** IO2**, **OW** (deck single wire memory), and **VCOM** (power supply). Please check out this [[projects:​crazyflie2:​expansionboards:​index|page]] to familiarize ​yourself ​with the pin-outs of the expansion decks. ​
  
  
Line 24: Line 24:
  
 <WRAP center round important 60%> <WRAP center round important 60%>
-We did not connect **IO3** on purpose since the Flow deck v2 is already using this for it's own, or else the LED deck and Flow deck will conflict with each other'​s communication with the Crazyflie.+We did not connect **IO3** on purpose since the Flow deck v2 is already using this, or else the LED deck and Flow deck will conflict with each other'​s communication with the Crazyflie. ​However, the LED deck should work as well without the IO3 connected
 </​WRAP>​ </​WRAP>​
  
-The battery holder deck can be glued on the LED-deck or attached with some tape.The wiring and soldering ​is done a bit crude for now to clearly show how to do this, however if you would like the wiring not to be shown as clearly as nowit should be very easy to do with thinner wires and basic soldering skills. =)+The battery holder deck can be glued on the LED-deck or attached with some tape.The wiring and soldering ​are done a bit crude for now to clearly show how to do this, however if you would like the wiring not to be shown as clearly as it is herethis should be easy to fix with thinner wires and basic soldering skills. =)
  
 +__Please pay attention to that the orientation of the LED deck is now different__. We put the battery holder on the side to prevent any connections to short with the LED deck, but now you would need to indicate the new '​front'​ of the LED deck. On the bottom left picture we show it with a sticker.
 +
 +{{:​misc:​hacks:​leddecktopcrazyflie.png?​800|}}
 +
 +We tested the converted LED deck with the Flow deck v2 with the CFclient and we are still receiving the values and parameters from both the deck drivers. At the moment of writing **we haven'​t test-flown this configuration yet**, but we hope to do it soon for another long exposure light painting!
  
  
  
  
misc/hacks/topleddeck.1559638650.txt.gz · Last modified: 2019-06-04 10:57 by kimberly