Bitcraze Wiki

User Tools

Site Tools

You are here: index » projects » crazyflie
Trace:
projects:crazyflie:index

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
projects:crazyflie:index [2011-11-22 08:02]
macke 		projects:crazyflie:index [2021-06-24 16:49] (current)
kimberly
Line 1: Line 1:
-====== CrazyFlie ======+<WRAP center round important 60%> 
 +This page has deprecated and will be archived. Please go to [[https://www.bitcraze.io/]]. 
 +</WRAP> 
 +====== Crazyflie 1.0 ====== 
 +The Crazyflie is a tiny quadcopter often referred to as a nano-quad, built using the PCB itself as the frame. Developed solely by open source tools and designed with development in mind. E.g. we choose 0603 components (resistors & caps) over 0402 to make it easier to replace components. The voltage regulators are adjustable which makes it possible to change the digital and analog supply voltages simply by changing a couple of resistors.
  
-===== Setup =====+**Features** 
 +  * Small and lightweight, around 19g and about 90mm motor to motor 
 +  * Flight time up to 7 minutes with standard 170mAh Li-Po battery 
 +  * Standard micro-USB connector for charging which takes ~20min for the stock 170mAh Li-Po battery 
 +  * On-board low-energy radio@1mW based on the nRF24L01+ chip. Up to 80m range (environment dependent) when using the Crazyradio USB dongle 
 +  * Radio bootloader which enables wireless [[doc:crazyflie:client:pycfclient:index#bootloader|update of the firmware]] 
 +  * Powerful 32 bit MCU: STM32F103CB @ 72 MHz (128kb flash, 20kb RAM) 
 +  * 3-axis high-performance MEMs gyros with 3-axis accelerometer: Invensense MPU-6050 
 +  * Available footprints to manually solder magnetometer HMC5883L/HMC5983 or/and barometer MS5611 (Mounted on the 10-DOF version) 
 +  * Expansion header 2×10 pins 1.27mm (0.05”) pitch including power, I2C/UART, SPI/ADC. Header also contains ARM Cortex 10-pin JTAG (header not included) 
 +  * 4-layer low noise PCB design with separate voltage regulators for digital and analog supply 
 +====== Using the Crazyflie ====== 
 +  * [[projects:crazyflie:userguide:index|User Guide/Introduction]]: Short user guide that introduces some basic concepts 
 +  * [[projects:crazyflie:mechanics:assembly|Crazyflie assembly]]: Instructions on how to assemble the Crazyflie kit 
 +  * [[[[misc:downloads:index|Download binaries]]: Download links for the binaries. 
 +  * [[projects:crazyflie:upgrading:index|Upgrading/flashing]]: How do upgrade/flash new firmware 
 +  * [[doc:crazyflie:client:pycfclient:index|GUI Application]]: Userguide for the Graphical user interface 
 +  * [[projects:crazyflie:pc_utils:install|Installation]]: Install instructions for PC side software 
 +  * [[projects:crazyflie:pc_utils:inputdevices|Input devices]]: What input devices are supported and how do you get them working 
 +  * [[projects:crazyflie:userguide:tips_and_tricks|Tips and tricks]]: Tips and tricks for flying 
 +  * [[projects:crazyflie:userguide:troubleshooting |Troubleshooting ]]: How to find and fix problems 
 +  * [[projects:crazyflie:safety|Safety Instructions ]]: Important instructions before and during flying 
 +  * [[projects:crazyflie:faq | FAQ]]: A list of frequently asked questions and the answers to them 
 +  * [[projects:virtualmachine:index | Bitcraze Virtual Machine ]]: Information about how to download and use the Virtual Machine 
 +  * [[doc:crazyflie:client:cfandroid:index|Android client user guide]]: Install instructions and user guide for the Crazyflie Android client 
 +====== Development ====== 
 +  * [[projects:contribution:index | How to contribute to the project]] 
 + 
 +===== PC/Host Environment ===== 
 +  * [[projects:crazyflie:pc_utils:dev_guide|Application dev. guide]]: Development guide for the PC side applications/library 
 +  * [[doc:crazyflie:api:python:index|Crazyflie Python Library]]: Documentation for the Python library used to communicate with the Crazyflie 
 + 
 +===== Android Environment ===== 
 +  * [[doc:crazyflie:dev:env:android|Android client dev. guide]]: Development guide for the Crazyflie Android client 
 + 
 +===== Firmware =====
   * [[projects:crazyflie:devenv:index|Development Environment]]: Setting up the compiler installing libs and fixing permissions for JTAG/radio dongles.   * [[projects:crazyflie:devenv:index|Development Environment]]: Setting up the compiler installing libs and fixing permissions for JTAG/radio dongles.
 +  * [[projects:crazyflie:firmware:arch|Overall firmware architecture]]
 +  * [[projects:crazyflie:firmware:comm_protocol|Communication protocol]]
 +  * [[projects:crazyflie:firmware:altitude_hold|Altitude hold mode]]
 +
 +===== Electronics =====
 +  * [[projects:crazyflie:hardware:explained| Crazyflie KIT electronics explained]]
 +  * [[misc:hacks:index | Crazyflie hacks and mods]]
 +  * [[projects:crazyflie:hardware:schematics | Crazyflie schematics]]
 +  * [[projects:crazyflie:hardware:spareparts | Spare components and where to order them]]
 +
projects/crazyflie/index.1321945358.txt.gz · Last modified: 2015-07-15 16:30 (external edit)

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki